Mercedes-Benz

Home / Mercedes-Benz

We Service and Repair all Mercedes-Benz cars

  • 2014 Mercedes-Benz C250

    Mercedes-Benz C250
    Mileage
    172,672
    Service Date
    8/25/2025
    Services Performed
    • CUSTOMER REQUESTS – REPLACE ALTERNATOR CUSTOMER SUPPLIED THE ALTERNATOR IN THE TRUNK
    • COMPLIMENTARY BATTERY AND ALTERNATOR TEST
    • ALTERNATOR ASSEMBLY – Remove & Replace – [Includes: Test.]
     
    Bella L. gave our service a 5 star review on 8/26/2025
  • 2004 Mercedes-Benz E320

    Mercedes-Benz E320
    Mileage
    110,221
    Service Date
    5/22/2025
    Services Performed
    • CUSTOMER REQUESTS – CHECK AND ADVISE NEW PURCHASE AND EXCHANGE WHAT EVER FLUIDS NEED ATTENTION,
    • RECOMMEND REPLACEMENT OF POWER STEERING PUMP, PUMP PRESSURE OUTPUT IS BELOW SPECIFIED VALUE.;
    • Multi-Point Inspection
    • All Fluids Checked and Topped up if possible
    • TRANSMISSION OIL PAN GASKET &/OR FILTER – Remove & Replace – Sedan
    • REMOVE AND REPLACE MOTOR OIL AND OIL FILTER, LUBE CHASSIS WHERE APPLICABLE, CHECK TIRE PRESSURE AND ALL FLUID LEVELS.
     
    Aaron T. gave our service a 5 star review on 5/22/2025
  • 2008 Mercedes-Benz E350

    Mercedes-Benz E350
    Mileage
    255,938
    Service Date
    12/13/2024
    Services Performed
    • AIR COND HOSE – Remove & Replace – From Expansion Valve/Evap,Suction – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
    • SERVICE AIR CONDITIONER. CHECK CONDITION OF ALL BELTS AND LINES. EVACUATE AND RECHARGE WITH R-134. TEST SYSTEM PERFORMANCE.
     
    Clayton B. gave our service a 5 star review on 12/14/2024
  • 2020 Mercedes-Benz C300

    Mercedes-Benz C300
    Mileage
    33,510
    Service Date
    10/16/2024
    Services Performed
    • REMOVE AND REPLACE MOTOR OIL AND OIL FILTER, LUBE CHASSIS WHERE APPLICABLE, CHECK TIRE PRESSURE AND ALL FLUID LEVELS.
    • Hazardous Waste Disposal Fee (Cal)
    • performed 42 point inspection and provide details to customer
    • INSPECT ALL HYDRAULIC LINE AND HOSES. INSPECT CALIPERS AND WHEEL CYLINDERS. INSPECT MASTER CYLINDER AND CAP. FLUSH ENTIRE BRAKE SYSTEM INCLUDING MASTER CYLINDER, CALIPERS, WHEEL CYLINDERS UNTIL CLEAN.
    • Hazardous Waste Disposal Fee (Cal)
    • Multi-Point Inspection
    • All Fluids Checked and Topped up if possible
     
    MARCIE E. gave our service a 5 star review on 10/16/2024
  • 2014 Mercedes-Benz E350

    Mercedes-Benz E350
    Mileage
    113,440
    Service Date
    12/13/2023
    Services Performed
    • REMOVE AND REPLACE MOTOR OIL AND OIL FILTER, LUBE CHASSIS WHERE APPLICABLE, CHECK TIRE PRESSURE AND ALL FLUID LEVELS.
    • Hazardous Waste Disposal Fee (Cal)
    • All Fluids Checked and Topped up if possible
    • performed 42 point inspection and provide details to customer
     
    Kristy I. gave our service a 5 star review on 12/13/2023
  • 2006 Mercedes-Benz C280

    Mercedes-Benz C280
    Mileage
    108,235
    Service Date
    12/7/2023
    Services Performed
    • REMOVE AND REPLACE MOTOR OIL AND OIL FILTER, LUBE CHASSIS WHERE APPLICABLE, CHECK TIRE PRESSURE AND ALL FLUID LEVELS.
    • Hazardous Waste Disposal Fee (Cal)
    • performed 42 point inspection and provide details to customer
    • All Fluids Checked and Topped up if possible
     
    Rita G. gave our service a 5 star review on 12/8/2023
  • 2014 Mercedes-Benz E350

    Mercedes-Benz E350
    Mileage
    108,510
    Service Date
    10/7/2023
    Services Performed
    • FOUND: found faults stored in PCM for intake manifold runner control, during inspection found intake manifold control solenoid connector to not be properly seated into solenoid, plugged in connector and cleared fault, did not return.
    • Remove and Replace Motor Oil and Oil Filter, Lube Chassis where applicable, Check tire pressure and all Fluid Levels
    • Hazardous Waste Disposal Fee (Cal)
    • performed 42 point inspection and provide details to customer
    • Rotate wheels, torque wheels to specification, and fill to appropriate pressure
    • SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Base,Sedan Both,w/o Air Suspension – [DOES NOT include alignment.]
    • DRIVE BELT TENSIONER – Remove & Replace – Sedan
    • TRANSMISSION OIL PAN GASKET &/OR FILTER – Remove & Replace – [Includes: Additional time for use of scan tool to perform this procedure.]
    • DIAGNOSTIC REFUND
     
    Kristy I. gave our service a 5 star review on 10/7/2023
  • 2011 Mercedes-Benz C300

    Mercedes-Benz C300
    Mileage
    107,252
    Service Date
    8/9/2023
    Services Performed
    • FOUND: Concern verified, steering column wont move up or down, back and forward OK, OBD2 code 9d90 The position sensor of the actuator motor for steering column up/down adjustment has a malfunction. Restarting the steering wheel column module will solve the problem but if come back—– Suggest replace up/down motor (pusition sensor built in motor) & code to new specs.
    • REMOVE AND REPLACE MOTOR OIL AND OIL FILTER, LUBE CHASSIS WHERE APPLICABLE, CHECK TIRE PRESSURE AND ALL FLUID LEVELS.
    • Hazardous Waste Disposal Fee (Cal)
    • performed 42 point inspection and provide details to customer
     
    Lowell P. gave our service a 5 star review on 8/16/2023
  • 2015 Mercedes-Benz C300

    Mercedes-Benz C300
    Mileage
    63,171
    Service Date
    9/30/2022
    Services Performed
    • BATTERY – Remove & Replace – Main – [Includes: Test.]
    • CA Battery Fee
     
    Jay C. gave our service a 5 star review on 10/7/2022
  • 2013 Mercedes-Benz C250

    Mercedes-Benz C250
    Mileage
    160,437
    Service Date
    1/4/2022
    Services Performed
    • FOUND: could not verify concern, however, found codes P0299 (Turbo boost pressure is too low) and P0128 ( Engine coolant temperature is below temperature) checked freeze frames and found p0299 to have been triggered twice, and p0128 to have been triggered 4 times, drove car on freeway for 15 minutes and found coolant temperature was not able to remain consistent at 90C, indicated thermsotat is stuck in an open position. replace thermostat. – Performed Tech Check for fault code p0299, smoke tested system for any vacuum leaks and found no leaks. inspected turbo charger wastegate actuator and found rod to be moving properly and wastegate to be properly moving. removed diverter valve to inspect turbo charger and found diverter valve diaphragm to be torn. likely root of concern, replace diverter valve.
    • THERMOSTAT – Remove & Replace
    • Turbocharger Diverter Valve – Remove & Replace
    • DIAGNOSTIC REFUND
     
    Alisa K. gave our service a 5 star review on 1/18/2022